Client: Florin Vancea
"Your product was the one that is good enough for what I needed, as well as it was good documented."
2.06Mb
4.0.0.74
25th October, 2007
1st June, 2009
Monitor and edit serial port data flows
Serial Port Sniffer ActiveX Control can monitor data flows, and moreover, edit them. It creates additional virtual COM port in the system with the same name as the monitored serial port.
All data that is sent to and from serial port goes to the virtual port created by this component and is being logged into special, defined document. You can substitute data chunks with the data of your own, thus influencing the process of COM port sniffing.
With Serial Port Sniffer ActiveX you can:
Replace data being sent between port and application with your own commands
Serial Port Sniffer ActiveX gives you the ability to influence the monitoring process. As all transmitted data is intercepted in the virtual port, created by our component, you can easily substitute it with any data characters and commands of your own to get deeper into the monitoring process.
Monitor data flows between COM port and application
With COM Port Sniffer ActiveX you will be able to fully monitor data flows between application and serial port. It allows you to detect control lines changes, handflow, baudrate and ring state changes, and track timeout updates. Serial Port Sniffer Components methods allow you to check whether the port is being sniffed, open the serial port to be sniffed and close the port after sniffing.
Take full control of all signal lines
Serial Port Sniffer ActiveX gives you the ability to influence the monitoring process. As all transmitted data is intercepted in the virtual port, created by our component, you can easily substitute it with any data characters and commands of your own to get deeper into the monitoring process.
Full features list:
- Monitor and edit serial data streams directly from your application
- Unique ActiveX Control - no need to use additional software for monitoring
- Wide selection of supported events, methods and properties
- Control lines support (DTR, RTS, CTS, RTS)
- Usage examples for Microsoft VC++ and Microsoft Visual Basic included
- No reboot required during installation and implementation
Demo version limitations:
- Reminder when invoking Start() method.
Interface languages:
Compatible with:
- Windows XP 32-bit
- Windows 2000
- Windows XP 64-bit
- Windows 2003 32-bit
- Windows 2003 64-bit
- Windows 2008 32-bit
- Windows 2008 64-bit
- Windows Vista 32-bit
- Windows Vista 64-bit
| # | Feature | Serial Monitor AX | Serial Sniffer AX |
|---|---|---|---|
|
1
|
Change DTR
|
 |
|
|
2
|
Change DSR
|
|
|
|
3
|
Change RTS
|
|
|
|
4
|
Change CTS
|
|
|
|
5
|
Open/Close port
|
|
|
|
6
|
Change Baudrate
|
|
|
|
7
|
Change Handflow control
|
|
|
|
8
|
Change Line control
|
|
|
|
9
|
Detect Ring
|
|
|
|
10
|
Write to port
|
|
|
|
11
|
Read from port
|
|
|
|
12
|
OnTimeouts
|
|
|
|
13
|
Change control chars
|
+(OnIrp)
|
 |
|
14
|
On/Off break
|
+(OnIrp)
|
|
|
15
|
Read data substitution
|
|
|
|
16
|
Write data substitution
|
|
|
|
17
|
Exact events timestamps
|
|
|
|
18
|
Read 6 Kb of data(sec)
|
6
|
10
|
|
19
|
Stop sniffing when port is opened
|
|
|
|
20
|
Start sniffing when port is opened
|
|
|
|
21
|
Trace the application that opened port
|
|
|